-- *****************************************************************
-- CISCO-LAG-MIB.my: Cisco LAG MIB
--
-- October 2001, Liwei Lue
--
-- Copyright (c) 2001-2003, 2004, 2006, 2008 by cisco Systems, Inc.
-- All rights reserved.
--
-- *****************************************************************CISCO-LAG-MIB DEFINITIONS::=BEGINIMPORTSMODULE-IDENTITY,OBJECT-TYPE,Unsigned32FROM SNMPv2-SMI
MODULE-COMPLIANCE,OBJECT-GROUPFROM SNMPv2-CONF
TEXTUAL-CONVENTIONFROM SNMPv2-TC
ciscoMgmt
FROM CISCO-SMI
dot3adAggPortEntry,dot3adAggPortListEntry
FROM IEEE8023-LAG-MIB
ifIndex
FROM IF-MIB;ciscoLagMIB MODULE-IDENTITYLAST-UPDATED"200801080000Z"ORGANIZATION"Cisco Systems, Inc."CONTACT-INFO"Cisco Systems
Customer Service
Postal: 170 W Tasman Drive
San Jose, CA 95134
USA
Tel: +1 800 553-NETS
E-mail: cs-etherchan@cisco.com
cs-lan-switch-snmp@cisco.com"DESCRIPTION"Cisco Link Aggregation module for managing IEEE Std
802.3ad.
This MIB provides Link Aggregation information that are
either excluded by IEEE Std 802.3ad (IEEE8023-LAG-MIB)
or specific to Cisco products."REVISION"200801080000Z"DESCRIPTION"Modified the description of clagAggPortListPorts."REVISION"200606210000Z"DESCRIPTION"Added clagAggMaxAggregatorsGroup and modified the
description of clagAggPortListPorts."REVISION"200406110000Z"DESCRIPTION"Added clagAggPortListTable."REVISION"200212130000Z"DESCRIPTION"Added a new value vlanIpPort(4) in TEXTUAL-CONVENTION
ClagDistributionProtocol.
Added a new object clagAggDistributionMplsProtocol."REVISION"200201020000Z"DESCRIPTION"Modified Description of clagAggDistributionProtocol."REVISION"200110230000Z"DESCRIPTION"Initial version of this MIB module.
Support Distribution configuration for LACP, Aggregation
protocol control, and Administrative status for LACP."::={ ciscoMgmt 225}clagMIBObjects OBJECTIDENTIFIER::={ ciscoLagMIB 1}-- -------------------------------------------------------------
-- Textual Conventions
-- -------------------------------------------------------------ClagDistributionProtocol ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"An enumerated type for all the supported load balancing
algorithms used on the LACP interface to distribute
outgoing data frames among its component interaces, such
as IP address.
ip(1) IP address
mac(2) MAC address
port(3) port number
vlanIpPort(4) vlan number, IP address and
port number"SYNTAXINTEGER{ip(1),
mac(2),port(3),vlanIpPort(4)}ClagDistributionAddressMode ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"An enumerated type for all the supported load
balancing address modes to distribute traffic
across multiple links. The address mode can be
source, destination, or both used on this LACP
interface to distribute outgoing data frames among
its component interfaces.
source(1) Source address.
destination(2) Destination address.
both(3) both, Source and Destination."SYNTAXINTEGER{source(1),destination(2),both(3)}ClagDistributionMplsProtocol ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION
"An enumerated type for all the supported load balancing
algorithms used on the LACP interface to distribute
outgoing MPLS (Multi-Protocol Label Switching) data
frames among its component interfaces, such as
MPLS label.
label(1) MPLS label
labelIp(2) MPLS label or IP address"SYNTAXINTEGER{label(1),labelIp(2)}ClagAggregationProtocol ::=TEXTUAL-CONVENTIONSTATUScurrent
DESCRIPTION"An enumerated type for all the supported aggregation
protocols.
lacp(1) Link Aggregation Control Protocol(LACP),
IEEE 802.3ad
pagp(2) Port Aggregation Protocol"SYNTAXINTEGER{lacp(1),pagp(2)}ClagPortAdminStatus ::=TEXTUAL-CONVENTIONSTATUScurrentDESCRIPTION"An enumerated type for all the LACP administrative states on
a particular aggregation port.
off(1) No LACP involved on the aggregation port.
on(2) The aggregation port always join link
aggregation whithout any LACP protocol
involved.
active(3) Active LACP indicates the port's preference
to participate in the protocol regardless of
Partner's control value.
passive(4) Passive indicates the port's preference for
not transmitting LACP PDU unless its Partner's
control value is Active LACP."SYNTAXINTEGER{off(1),on(2),
active(3),passive(4)}-- -------------------------------------------------------------
--
-- -------------------------------------------------------------
-- groups in the LAG MIB
-- -------------------------------------------------------------clagGlobalConfigObjects OBJECTIDENTIFIER::={ clagMIBObjects 1}clagAgg OBJECTIDENTIFIER::={ clagMIBObjects 2}
clagAggPort OBJECTIDENTIFIER::={ clagMIBObjects 3}clagAggPortList OBJECTIDENTIFIER::={ clagMIBObjects 4}-- -------------------------------------------------------------
--
-- -------------------------------------------------------------
-- The Aggregation Global Configuration
-- -------------------------------------------------------------clagAggDistributionProtocol OBJECT-TYPESYNTAX ClagDistributionProtocol
MAX-ACCESSread-write
STATUScurrentDESCRIPTION"This object controls the load balancing algorithms
used on this LACP interface to distribute outgoing data
frames among its component interfaces."::={ clagGlobalConfigObjects 1}clagAggDistributionAddressMode OBJECT-TYPESYNTAX ClagDistributionAddressMode
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The load balancing address mode for the device."::={ clagGlobalConfigObjects 2}
clagAggDistributionMplsProtocol OBJECT-TYPESYNTAX ClagDistributionMplsProtocol
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"This object controls the load balancing algorithms
used on this LACP interface to distribute outgoing MPLS
data frames among its component interfaces.
This object is only instantiated on platforms which
support aggregation load balancing for MPLS packets."::={ clagGlobalConfigObjects 3}clagAggMaxAggregators OBJECT-TYPESYNTAXUnsigned32
MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object indicates the maximum number of aggregators
supported by the device."::={ clagGlobalConfigObjects 4}-- -------------------------------------------------------------
-- The Aggregation Protocol Table
-- -------------------------------------------------------------clagAggProtocolTable OBJECT-TYPESYNTAXSEQUENCEOF ClagAggProtocolEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"A table that contains protocol information about every
interface which supports link aggregation."::={ clagAgg 1}clagAggProtocolEntry OBJECT-TYPESYNTAX ClagAggProtocolEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"Entry containing aggregation protocol type for a
particular interface. An entry is created in this
table when its associated ifEntry is created and that
interface supports link aggregation. The entry of this
table is deleted when the associated ifEntry is removed."INDEX{ ifIndex }::={ clagAggProtocolTable 1}
ClagAggProtocolEntry ::=SEQUENCE{
clagAggProtocolType ClagAggregationProtocol
}clagAggProtocolType OBJECT-TYPESYNTAX ClagAggregationProtocol
MAX-ACCESSread-writeSTATUScurrentDESCRIPTION"The aggregation protocol type for the interface.
On some platforms, aggregation protocol may be assigned per
group. The group can be a collection of the ports which belong
to a module or system. If the aggregation protocol is assigned
to any of the ports in such group then the aggregation protocol
will apply to all ports in the same group.
On some platforms, aggregation protocol type can be assigned
per aggregator. If multiple ports belong to a aggregator,
the aggregation protocol assigned to any of the ports in such
aggregator will apply to all ports in the same."::={ clagAggProtocolEntry 1}-- -------------------------------------------------------------
-- The Aggregation Port Configuration Table
-- -------------------------------------------------------------clagAggPortTable OBJECT-TYPE
SYNTAXSEQUENCEOF ClagAggPortEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A table that contains information about every
aggregation port that is associated with this system.
This table contains additional objects for the
dot3adAggPortTable."REFERENCE"IEEE 802.3 Subclause 30.7.2"::={ clagAggPort 1}clagAggPortEntry OBJECT-TYPESYNTAX ClagAggPortEntry
MAX-ACCESSnot-accessible
STATUScurrentDESCRIPTION"An entry containing additional management information
applicable to a particular aggregation port."AUGMENTS{ dot3adAggPortEntry }::={ clagAggPortTable 1}
ClagAggPortEntry ::=SEQUENCE{
clagAggPortAdminStatus ClagPortAdminStatus
}clagAggPortAdminStatus OBJECT-TYPESYNTAX ClagPortAdminStatus
MAX-ACCESSread-writeSTATUScurrent
DESCRIPTION"The administrative status of the LACP protocol on this
aggregation port."::={ clagAggPortEntry 1}-- -------------------------------------------------------------
-- The Port List Table
-- -------------------------------------------------------------clagAggPortListTable OBJECT-TYPESYNTAXSEQUENCEOF ClagAggPortListEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"This table augments the dot3adAggPortListTable and
provides the complete list of ports associated with
each Aggregator."REFERENCE"IEEE 802.3 Subclause 30.7.1.1.30"::={ clagAggPortList 1}clagAggPortListEntry OBJECT-TYPESYNTAX ClagAggPortListEntry
MAX-ACCESSnot-accessibleSTATUScurrentDESCRIPTION"A list of the ports associated with a given Aggregator."AUGMENTS{ dot3adAggPortListEntry }::={ clagAggPortListTable 1}
ClagAggPortListEntry ::=SEQUENCE{
clagAggPortListPorts OCTETSTRING}clagAggPortListPorts OBJECT-TYPESYNTAXOCTETSTRING(SIZE(2..256))MAX-ACCESSread-onlySTATUScurrentDESCRIPTION"This object contains a list of ports currently associated
with this Aggregator in the format of
'[number_of_ports][cieIfDot1dBaseMappingPort1][...]
[cieIfDot1dBaseMappingPortn]'
where
[number_of_ports] is of size 2 octet and indicates
the number of ports contains in this object. It
also indicates the number of cieIfDot1dBaseMappingPort field
following this field.
[cieIfDot1dBaseMappingPort'n'] is the value of
cieIfDot1dBaseMappingPort of the 'n' port associated with this
Aggregation and has size of 2 octets where n is up to
[number_of_ports]."REFERENCE"IEEE 802.3 Subclause 30.7.1.1.30"::={ clagAggPortListEntry 1}-- -------------------------------------------------------------
--
-- -------------------------------------------------------------
-- Notifications
-- -------------------------------------------------------------clagMIBNotifications OBJECTIDENTIFIER::={ ciscoLagMIB 2}-- no notifications defined
--
-- -------------------------------------------------------------
-- Conformance
-- -------------------------------------------------------------clagMIBConformance OBJECTIDENTIFIER::={ ciscoLagMIB 3}clagMIBCompliances OBJECTIDENTIFIER::={ clagMIBConformance 1}
clagMIBGroups OBJECTIDENTIFIER::={ clagMIBConformance 2}-- -------------------------------------------------------------
--
-- -------------------------------------------------------------
-- Compliance
-- -------------------------------------------------------------clagMIBCompliance MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for entities which implement
the Cisco Link Aggregation MIB"MODULE-- this moduleMANDATORY-GROUPS{
clagAggProtocolGroup,
clagAggPortGroup
}GROUP clagAggDistributionGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing."OBJECT clagAggProtocolType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT clagAggPortAdminStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ clagMIBCompliances 1}
clagMIBCompliance2 MODULE-COMPLIANCESTATUSdeprecatedDESCRIPTION"The compliance statement for entities which implement
the Cisco Link Aggregation MIB"MODULE-- this moduleMANDATORY-GROUPS{
clagAggProtocolGroup,
clagAggPortGroup
}GROUP clagAggDistributionGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing."GROUP clagAggDistributionMplsGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing for MPLS
packets."OBJECT clagAggProtocolType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT clagAggPortAdminStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ clagMIBCompliances 2}clagMIBCompliance3 MODULE-COMPLIANCESTATUSdeprecated
DESCRIPTION"The compliance statement for entities which implement
the Cisco Link Aggregation MIB"MODULE-- this moduleMANDATORY-GROUPS{
clagAggProtocolGroup,
clagAggPortGroup
}GROUP clagAggDistributionGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing."GROUP clagAggDistributionMplsGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing for MPLS
packets."GROUP clagAggPortListGroup
DESCRIPTION"This group is mandatory for the devices which
supports dot1dBasePort value greater than 2048."OBJECT clagAggProtocolType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."OBJECT clagAggPortAdminStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ clagMIBCompliances 3}
clagMIBCompliance4 MODULE-COMPLIANCESTATUScurrentDESCRIPTION"The compliance statement for entities which implement
the Cisco Link Aggregation MIB"MODULE-- this moduleMANDATORY-GROUPS{
clagAggProtocolGroup,
clagAggPortGroup
}GROUP clagAggDistributionGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing."GROUP clagAggDistributionMplsGroup
DESCRIPTION"This group is mandatory for the devices which
supported aggregation load balancing for MPLS
packets."GROUP clagAggPortListGroup
DESCRIPTION"This group is mandatory for the devices which
supports dot1dBasePort value greater than 2048."GROUP clagAggMaxAggregatorsGroup
DESCRIPTION"This group is mandatory for the devices which
provides the information about the maximum number
of aggregators supported by the device."OBJECT clagAggProtocolType
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."
OBJECT clagAggPortAdminStatus
MIN-ACCESSread-onlyDESCRIPTION"Write access is not required."::={ clagMIBCompliances 4}-- -------------------------------------------------------------
-- Units of Conformance
-- -------------------------------------------------------------clagAggProtocolGroup OBJECT-GROUPOBJECTS{ clagAggProtocolType }STATUScurrentDESCRIPTION"The object that provide aggregation protocol type of an
interface. These are additional to the IEEE Std 802.3ad
MIB."::={ clagMIBGroups 1}clagAggPortGroup OBJECT-GROUPOBJECTS{ clagAggPortAdminStatus }STATUScurrentDESCRIPTION"A collection of objects that provide admin status
about an aggregation port. These are additional to the
IEEE Std 802.3ad MIB."::={ clagMIBGroups 2}clagAggDistributionGroup OBJECT-GROUPOBJECTS{
clagAggDistributionProtocol,
clagAggDistributionAddressMode
}STATUScurrentDESCRIPTION"A collection of objects that provide the load balancing
information for an aggregator. These are additional to
the IEEE Std 802.3ad MIB."::={ clagMIBGroups 3}clagAggDistributionMplsGroup OBJECT-GROUPOBJECTS{ clagAggDistributionMplsProtocol }STATUScurrentDESCRIPTION
"A collection of objects that provide the load balancing
information for an aggregator for MPLS packets.
These are additional to the IEEE Std 802.3ad MIB."::={ clagMIBGroups 4}clagAggPortListGroup OBJECT-GROUPOBJECTS{ clagAggPortListPorts }STATUScurrentDESCRIPTION"A collection of object that provides information about
ports in an aggregation."::={ clagMIBGroups 5}clagAggMaxAggregatorsGroup OBJECT-GROUP
OBJECTS{ clagAggMaxAggregators }STATUScurrentDESCRIPTION"A collection of object that provides information about
the maximum number of aggregators supported by the
device."::={ clagMIBGroups 6}END